Tuesday, November 25, 2014

DFDP-2 @ 547 m, drilling equipment

Rupert Sutherland, GNS Science and Victoria University of Wellington
John Townend, Victoria University of Wellington
Virginia Toy, University of Otago

DFDP-2 drill site from the bridge over Whataroa River.13/11/14. Photo R. Sutherland. 
Exploration can present logistic challenges, because any trip into the unknown may hold surprises. In the case of our drilling experiment, the challenges we face include: having the right drilling equipment; attracting and sustaining a strong team of people for many months; and extracting scientific results from challenging underground conditions (e.g. the high temperatures that we have already encountered).

Obtaining and maintaining the right drilling equipment has proven tougher than expected and we are now several weeks behind schedule.

The current drilling method we are using breaks the rock into small pieces (cuttings) and creates a 215 mm diameter open hole. It is a similar method to that employed by the petroleum industry, but we are drilling into a much harder rock than they typically encounter. Hard rocks similar to our site are commonly drilled by mineral explorers (e.g. gold miners), but they usually collect rock cores and drill a much smaller (<125 mm) and shallower hole. It is hard to find a drilling company with such overlapping experience. The NZ contractors we have on the job (Webster Drilling and Eco Drilling) have been very helpful and are learning with us.

This video shows you what the business end of our open hole drilling gear looks like:

We reached 547 m depth last Wednesday (17/11/14), but progress was slow and equipment was damaged. A decision was made to remove all drilling equipment from the hole, send it to Christchurch for a makeover, and obtain new specialised drill bits. The new roller-cone drill bits have hardened points to shatter the rock, but they need several tons of weight on them to be effective.

We hope to start drilling again tomorrow.

Photos of different (used) drill bits: 
(A) Coring drill bit with industrial diamonds for hard rock
 – the hole in the middle is where rock core enters; 

(B) PCD, Poly-Crystalline Diamond, bit for an open hole;
(C) Roller-cone bit designed for soft rock (damaged bit).
Primary funders of the DFDP-2 project are: the International Continental Scientific Drilling Program (ICDP), the Marsden Fund of the Royal Society of New Zealand, GNS Science, Victoria University of Wellington, and the University of Otago.


  1. Since drilling machines make big change in constructions work. Most of the time drilling machines takes high power or electricity consumption during work.

    For more information please visit our website :- http://www.tasmanoiltools.com.au

  2. we have probably seen the equipment before.
    Our consultants will use their experience from many sites to ensure that critical to quality parameters are considered during this process.
    We've seen what works and what definitely doesn't.

    equipment validation
    labview programming
    software validation

  3. it is important to have the right drilling equipment. You never know what materials you will have to drill through as you break the surface of the earth. I never knew that there were machines that make small cuttings as you talk about it.
    Mark Leach | http://www.acmachineworks.com/en/services.html

  4. Any single group must be subjected to the 3 validation cleaning requirement,
    except if a rationale is recorded and also approved by the Standard Authority
    which the worst-case product of one group is clearly a worst-case product for every one of the groups.
    Software validation is a part of the design validation for a finished device,
    but is not separately defined in the Quality System regulation.

    equipment validation

  5. we are offering the best products in drilling machines, its equipments. we are committed to developing a best quality products to our customers. please visit us at http://www.pankajinternational.com/


  6. Focuses on the validation of laboratory equipments used in the production of pharmaceutical products.
    Determination the requirements of the end user,
    which are often defined in the User Requirements Specifications.equipment validation is a part of the design validation for a finished device,
    but is not separately defined in the Quality System regulation.

    equipment validation

  7. The ability of prerequisites to streamline the execution of a qualification,
    with the added bonus of the ways that they benefit a quality system,
    demonstrates the value of incorporating prerequisites into an equipment qualification.This service saves you time and money,
    as you can review these digital representations.

    equipment validation

  8. we have probably seen the equipment before.
    Zhejiang Yaang Pipe Industry Co., Limited is a leading manufacturer and supplier of nickel alloy and stainless steel products, including Super Duplex Stainless Steel Flanges, Stainless Steel Flanges, Stainless Steel Pipe Fittings, Stainless Steel Pipe, Ball Valves. Yaang products are widely used in Shipbuilding, Nuclear power, Marine engineering, Petroleum, Chemical, Mining, Sewage treatment, Natural gas and Pressure vessels and other industries. For more information visit: www.yaang.com

  9. It is 100% recyclable.Did you know that about 50% of all new stainless steel comes from scrap materials? Yes, you heard that right! It can be recycled for infinite number of times without losing its strength.

    Alloy Products